How to Open Xbox One Controller Without Torx?

When it comes to Xbox controllers, 7 out of 10 of them will shatter if dropped. What if the controller falls and something goes wrong inside, and you realize that you don’t have any Torx screwdrivers to open the dang thing? Then How to Open Xbox One Controller Without Torx?

In any case, don’t worry about it, my friend, because I’ve laid out a series of instructions on how you should proceed. Find out by continuing to read.

How to Open Xbox One Controller Without Torx?

How to Open Xbox One Controller Without Torx

For small screws in electronics, a Torx screwdriver is a type of Phillips screwdriver. To remove the screws from an Xbox game console, a size 10 Torx screwdriver is typically utilized.

But if you can’t get hold of a Torx 10 screwdriver, you can open the Xbox with an ordinary screwdriver. As long as the screwdriver is small enough to fit into the grooves of the screws, it won’t affect the disassembly process.

Disconnect the controllers from the connectors on the front of the Xbox and turn it off.

Take your flat-head screwdriver and use it for popping the four rubber screw covers from each corner on your Xbox one’s bottom. Pry up the two console information stickers with the flat-head screwdriver tip.

Remove each of the four corner screws with a Phillips-head screwdriver and place them in a safe place. Identify the two screws hidden beneath each sticker and remove them. Afterward, dispose of them.

Lift the top frame of your Xbox from the sides as you turn it right side up. You can put the entire frame away now. After a brief delay, the Xbox has been activated.

What Screwdriver to Open Xbox Series X Controller?

You can use a T6 or T8H screwdriver, the Xbox One controller, the Xbox One Elite Wireless Controller, and the Xbox 360 controller can all be opened.

How to Open Xbox One Controller With Torx?

Step #1)

Unplug the battery pack from the controller’s rear.

Step #2)

To gain access to the Torx screws on the front and rear panels of the gamer, remove the handle covers. I suggest using a little plastic trim tool to open the handle. Gently take the plastic cover off using a flathead screwdriver. 

It is here where the front, side and rear mouldings come together that you place the flathead screwdriver’s trim plastic into the base of the handle. Once you’ve got a grip of the edge, use your fingers to peel it away from the controller.

Step #3)

It’s time to get to work on that Torx screw. If you remove the warranty sticker, you can discover this screw. In order to separate the back and front of the controller, this screw is required. 

Your warranty will be void if you use a screwdriver to make a hole in the middle of the sticker. To begin with, remove the screws with a standard screwdriver and then store them in an appropriate location.

Step #4)

Remove the remaining screws from the controller with a Torx wrench. ‘ You will need to remove all four remaining screws. 

If you don’t have a Torx screwdriver, use a flathead one, but be careful not to use too much power, or you could damage the screws. 

Remove them from the controller and store them in a secure place for when you reassemble them.

Step #5)

Remove the controller’s back and front panels. You can now lift the controller’s back and front panels off its mainframe after removing the Torx screws, and the side handles. Even so, there are no exposed wires and other circuitry.


How to Take Apart Xbox Series X Controller?

Warning: You will void the warranty on your Xbox if you open it.


FAQs – How to Open Xbox One Controller Without Torx

What can I use if I don’t have a Torx screwdriver?

In place of a Torx screwdriver, what may you use? Occasionally, an Allen key or a flat blade screwdriver can become stuck between two points in the recess and get the job done. Damaged screws and tools can necessitate the need for replacement.

What screwdriver Do you need to open up an Xbox controller?

Xbox One, Elite Wireless and Xbox 360 controllers can be opened using a T6 T8H screwdriver.

Can you use hex instead of Torx?

Instead of utilising a hex key or Allen wrench, we suggest using your Torx wrenches. It’s also worth noting that the T9 Torx size isn’t compatible with any SAE sizes. However, the 2.5 mm metric size is a perfect fit.

How do you remove a Torx without a Torx?

Try out a plastic toothbrush first. You can use a lighter or another heat source to soften the end of a plastic toothbrush. The plastic can then be inserted into the screw head and allowed to harden again. You can unscrew the screw by twisting it counterclockwise.

How do I clean my Xbox One without compressed air?

1: Remove the console’s power cable and unplug it from the outlet.
2: Wipe off the entire Xbox’s surface and exterior with a microfiber cloth dampened with rubbing alcohol or mild soap and water.


Conclusion

As you can see, you don’t need a Torx screwdriver to open your controller; in fact, you can do it without one with relative ease. After reading this article, I hope you know “how to open Xbox one controller without Torx“.

Read More: